|
|
|
|
 
|
|
|---|
Video game parts and electronic game parts for sale including this standard video game jama harness to install jama compatible games in game cabinets. Jama edge connector is labeled for easy wiring of your new game.
New replacement fluorescent lamp ballast for 14 to 20 watt bulbs. Works with F14T8, F15T8, F14T12, F15T12 or F20T12 lamps.
New replacement fluorescent lamp starters for many wattages of lamps. FS-2 for 4-22 watt bulbs, FS-5 for 4-6-8 watt bulbs, FS-25 for 25 watt bulbs and FS-4 for 30-40 watt bulbs.
New replacement 2700K 13 watt/120 volt fluorescent bulb unit.
Light bulbs commonly found on arcade games. They come 10 to the pack. Choose the bulb type needed below. #47, #55, #161, #555, #1892, #1895, #74, #89, #912, and #455 are available. #47 is a direct replacement for #44 bulbs and #455 are flasher bulbs.
Colored #555 bulbs used in many different arcade games.
Colored #44 bulbs used in many different arcade games.
#5G9 24V bulb. 24 volt screw base bulb for all Sports Arena and similar games. Available in red or clear.
24 Volt 7 watt bulb with screw in base for all Super Sports Arena games. Available in clear only.
These lamp sockets accept bayonet base lamps such as #44, 47 and #55 bulbs. Replacement socket for most older pinball games using these bayonet bulbs.
These lamp sockets accept bayonet base lamps such as #44, 47 and #55 bulbs and are designed to mount side ways. Replacement socket for most older pinball and video games using these bayonet bulbs.
This (3" x 5/16" diameter) rubberized abrasive lamp socket cleaning stick is great for cleaning out the inside of lamp sockets to shine up the connections within it.
Battery box or holder for most newer pinballs using replaceable AA alkaline batteries.
Black plastic battery box or holder for Williams pinballs using replaceable AA alkaline batteries.
110 volt male plug for all video games. Easy replacement.
Electrohome G07 Monitor Flyback Transformer.
2SD870 output transitor for the G07 monitors chassis.
Hortizonal width coil for Electrohome G07 monitor chassis.
Monitor Capacitor Parts Kit. Replaces all the old and dried out capacitor parts in these monitor chassis. Fixes most problems with poor pictures.
High current bridge rectifier #MBR506W used on many pinballs and video games. Has wire legs and can handle 50 to 1000 volts and 50 amps. $14.95.
New universal replacement 15 amp video game power supply.
Switching power supply for Cruising USA and other arcade games. Has 9 pin molex plug. +5V at 16A, +12V at 6A, -5V at 5A and -12V at 5A.
Switching power supply for Off Road Challenge and other similar arcade games. Has 12 pin molex plug and one standard computer power plug. +5V at 20A, +12V at 8A, -5V at .5A and -12V at .5A.
Line filter for all game machines. 6 amp capacity.
5K ohm pot used on many arcade games for steering and accellerator controls.
Volume control L-Pad. Makes adjusting volume control easy on games with difficult volume control access. Easy series speaker line installation.
Replacement fuse holder has screw hole for easy mounting. 1/4" lugs for easy wire attachment.
Replacement fuse clip used in many arcade and pinball machines. This clip solders into two small holes in a PC board. Fuse Clip is 1/4 in wide; Snap Mount; 15 A (Max.) Two required to make up one fuse holder.
AGC Fast Blowing Fuses
MDL Slow Blowing Fuses
8AG series fuses are shorter in length than standard fuses and measure 1" long. 6MA series fuses are shorter in length than standard fuses and are 3/4" long.
Used working Pacman and Ms Pacman logic boards ready to plug into your cabinet.
We accept secure online credit card payments via PayPal Payment Services
lakeside@moneymachines.com
Lakeside Distributors